Add src/pattern/ module with 3 engine patterns:
- Breathe: smooth ramp up/down (~2.5s cycle, 1 engine)
- Heartbeat: double-pulse with long rest (~1.6s cycle, 1 engine)
- RGB cycle: phase-offset breathing via trigger sync (3 engines)
Patterns support both RGBW and 3-channel monochrome LED modes via
LED_MAP configuration. Main loop cycles through all 3 patterns (8s
each) while LP5562 runs them autonomously — MCU just idles.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Add error-resilient firmware with diagnostic LED blink patterns
(3 slow = alive, solid = I2C OK, fast burst = I2C error). Document
EVM external MCU wiring: disconnect P6 EN jumper, power VDD from
XIAO 5V, leave SCL/SDA jumpers in place with MSP430 unpowered.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Reverse-engineered the MSP430 serial protocol on the LP5562EVM:
- I<addr><reg> reads, O<addr><reg><data> writes, status 00=OK / 02=NAK
- EN pin must be jumpered to VDD (MSP430 doesn't drive it after reset)
- CONFIG (0x0B) is write-only, W_CURRENT (0x09) not writable via bridge
- LED cycling verified: all 4 channels respond to direct PWM control
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
The uFR Zero presents as CCID (not serial), so the uFCoder library
cannot communicate with it. Rewrote ntag5_config_check.py to use
pyscard with auto-detection: ACR1552 for full NXP config verification,
generic PCSC for basic tag info. Removed uFCoder library (unusable).
Backed up CCID Info.plist before adding uFR Zero VID:PID entry.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
- Hall sensor + LP5562 EN wired-AND circuit design (DRV5032FB/FE,
1M pull-up, open-drain topology) with three interaction modes:
boot-time recovery, tap-to-swap, hold-to-confirm recovery
- NTAG5 config check tool (tools/ntag5_config_check.py) using
uFCoder library for ISO15693 transparent mode via uFR Zero reader.
Supports inventory + addressed mode for multi-tag fields.
- Updated DEVELOPMENT_PLAN with I2C bus management notes for
LP5562 (0x30) + NTAG5Link (0x54) shared bus
- Updated README with wired-AND hardware diagram, hall sensor
interaction section, and updated wiring table
- Updated CLAUDE.md with LP5562 EN wired-AND topology docs
- Updated STATUS.md with hall sensor decisions and hardware inventory
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
- Integrate LP5562 driver from sibling project (ntag5-samd21-lp562)
with full doc comments restored
- Update main.rs with complete M1 test: I2C init, GPIO EN, RGBW cycle
- Rewrite DEVELOPMENT_PLAN.md from waterfall to milestone-based groups
organized by hardware availability (Groups A-E)
- Rewrite STATUS.md with milestone checklist tracking
- Add LP5562 timing constraints and flash script docs to CLAUDE.md
- Add flash_when_ready.sh for auto-flash dev workflow
- Add brainstorm design doc for plan redesign rationale
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Set up Rust embedded project targeting SAMD21 (thumbv6m-none-eabi) with
XIAO M0 BSP for dev board prototyping. Includes LP5562 EN pin control
on D0/A0, project documentation (README, CLAUDE.md), phased status
tracker, and detailed development plan covering LP5562 driver integration,
NTAG5Link I2C driver, pattern storage format, power management, NFC
communication protocol, recovery mode, and firmware update strategy.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
